menu
ITEMS ADDED TO THE BASKET

t: 01323 737320 |
BASKET
FREE DELIVERY FREE DELIVERY When you spend over £15
PRICE MATCH PRICE MATCH *Contact us with your enquiry
FULL BIKE CHECK FULL BIKE CHECK Built and checked before sending
4.5 Google reviews 4.5 Google reviews 4.5 Google reviews
OneUp EDC Tap Kit

OneUp EDC Tap Kit

Available to order
$40.09
e: / t: 01323 737320

THE DETAIL

TAPPING INSTRUCTIONS

Remove your old star-nut and tap the top of your steerer tube. This might sound daunting, but we've made it super easy to do on your bike, without even removing your fork.

    Remove your bar and stem
    Use the OneUp star-nut puller to remove your old star nut
    Using the self aligning steerer tap kit, tap a thread into your steerer until the tap bottoms out.

SEE VIDEO and detailed instructions below. Please read entire instructions and consult your local bike shop if you are uncomfortable with performing the tapping procedure.  

 

SPECIFICATIONS

FORK COMPATIBILITY

EDC Tool, Fork Install Requirements
To install the EDC tool into your fork you need to remove your old star-nut and tap the top of your steerer tube. This might sound daunting, but we've made it super easy to do on your bike, without even removing your fork.

    Remove your bar and stem
    Use the OneUp star-nut puller to remove your old star nut
    Using the self aligning steerer tap kit, tap a thread into your steerer until the tap bottoms out.

EDC can only be fitted to your fork if all of the requirements below are met. Don't worry if your fork is not compatible the EDC tool has also been designed to be stored inside our new high volume pump with bottle cage mount.

Fork Requirements:
The EDC Top Cap Kit is only compatible with 1.5" Tapered mountain bike forks with an aluminum steerer tube. Carbon and Steel steerer tube forks are NOT compatible.
To install EDC in your fork you must have at least 3mm of steerer tube above your stem when installed and use a minimum 5mm headset spacer above your stem. A 10mm headset spacer stack above your stem is recommended. You will need to check the 4 dimensions below (A, B, C, D)
A - Total Steerer Tube Length
Steerer tube length measured from bottom of crown to top of the steerer must be 183-230mm long (7.25-9.00"). Use a tape measure to check length.

B - Steerer Tube Star Nut Diameter
The inner diameter must be between 24.25 mm-24.80 mm. To check, this will require a OneUp "Go, No-Go Gauge" or a good set of calipers (that your local shop should have). If you have a Fox 32 we recommend checking this before ordering the tap and gauge kit as some models have steerers that are outside this range. Otherwise it is very unlikely you will have an issue.

C - Steerer tube Min Diameter
Minimum diameter 22.1 mm (0.87"). To check, you can push a 16g or 20g CO2 cannister or a standard mtb handlebar up through the hole in the bottom of your fork steerer. If you can touch your star nut, you're all good.  

D - Steerer tube Max Diameter (opening in the underside of your fork crown)
31.75 mm - 34.00 mm dia. (1.25-1.34"). This is to ensure the EDC fork plug can be fitted. This is not essential, but ensures the EDC tool cannot rattle inside your fork.

Forks that at NOT Compatible
- All Forks with Carbon fiber or Steel Steerers
- All Cannondale Lefty Forks
- Some Fox 32 forks - See "Steerer Tube Star Nut Diameter" above to confirm
- 2012-2015 Fox 34 29 Forks - See "Steerer tube Min Diameter" above to confirm
- All Giant Overdrive 2 Forks

Forks with non-standard setups
- 2016+ SRAM Pike Boost *
- 2016+ SRAM Lyrik Boost *
- All Ohlins RXF series Forks **

*Storage capsule will fit, but CO2 cartridges may not.
** EDC Fork plug will not fit

 

OK
By accepting or continuing to browse this site, you are agreeing to our use of cookies and our privacy policy